At your location in just 29 minutesGet the measurements right away.T&C

Illustration: Small fragments of shattered toughened glass beneath an aluminium partition frame

Table tops and mirrors · Bengaluru, Delhi NCR, Mumbai MMR and Pune

Toughened Glass Broke by Itself? Causes & Repair Cost

Toughened glass can break with nobody near it, and the pieces usually tell you why.

₹520/ sq ft starting price

The starting price for Broken Glass Replacement, the commonest fix. You pay this rate for the square feet we measure on site.

  • Verified on-site measurement
  • 2-year product warranty, 6 months on the work
  • Fitted by our own team. We never subcontract.
Also searched as

The short answer

Toughened glass rarely breaks for no reason, even when nobody touched it. The usual causes are a tiny nickel sulphide inclusion from manufacture, or an edge chip that spread later. A hinge, clamp or bolt tightened too hard on the glass does it too. The glass bursts into small blunt cubes, which is what makes it safety glass. We clear the pieces, make the opening safe and fit a new toughened panel made to your sizes.

The useful distinction

A butterfly pattern at the centre points away from any knock

Two small wedges meeting at one point usually mark where the break began. A start at an open edge often follows a chip from earlier. A start under a hinge, clamp or bolt points to that fitting instead.

Why it happens

Usually one of these 4 things, commonest first. Each one says how to tell, and what we do about it.

  1. A nickel sulphide inclusion inside the glass has grown

    How to tell
    Nickel sulphide is a speck of impurity that can get into glass while it is made. Over months or years the speck slowly swells inside the toughened panel. One day the stress is too much, and the panel bursts with nobody near it.
    What we do
    We clear the glass, take the pieces away and measure for a new panel. Where you want less risk we suggest heat-soaked glass. It is baked after toughening, so a weak panel fails at the factory and not in your home.
    Broken Glass ReplacementFrom ₹520 / sq ftSee this fix
  2. An edge chip from fitting or cleaning has finally spread

    How to tell
    The break started at an edge or a corner, not the middle. Toughened glass holds its strength in a skin of stress along its surface. A chip at the edge breaks that skin, and the crack can wait weeks before it runs.
    What we do
    We fit a new panel and check how its edges sit in the frame or fittings. Edges that touch metal get a rubber packer, the soft strip that keeps glass and metal apart.
    Broken Glass ReplacementFrom ₹520 / sq ftSee this fix
  3. A railing clamp was tightened too hard on the glass

    How to tell
    The pieces fell away from a clamp or a base shoe first. The gasket inside the clamp, its rubber liner, had worn thin or was missing. Metal was pressing on the glass with every gust of wind.
    What we do
    We fit new clamps with fresh gaskets and tighten them snug, never hard. The panel sits on rubber at every point, so no clamp can pinch it again.
    Glass Railing Clamp ReplacementFrom ₹425 / clampSee this fix
  4. A balcony panel was pinched as it expanded in the sun

    How to tell
    A balcony panel is in sun for hours, then cools fast in rain or at night. Glass set tight in a frame with no room to move takes that strain. The break often starts where the panel meets a frame corner.
    What we do
    We fit a new balcony panel with a small gap all round for movement, held on rubber. For a railing on a high floor we usually suggest laminated glass. That is two sheets with a plastic layer between, which holds its pieces if it ever breaks.
    Balcony Glass ReplacementFrom ₹553 / sq ftSee this fix

What you can check first

These checks are safe to do yourself. A photo or a short video of what you find helps us come prepared.

  • Photograph the pieces before anyone sweeps up, especially any spot where two wedges meet.
  • Look at every fitting the panel sat in, and whether a rubber liner is missing or crushed.
  • Check whether the glass had a chip or a small star mark at an edge before it broke.
  • Look at the other panels for chips at their edges, without touching them.

Keep away from any panel that has cracked but not fallen. Toughened glass that has started to break can finish at any moment. On a balcony or staircase, keep children and pets off that side until the glass is cleared. Do not try to lift a cracked panel out yourself.

What the repair costs

Every fix on this page, with its starting price before GST. We find which one you need, and you get a fixed price before any work starts.

FixStarting priceHow it is pricedLink
Broken Glass Replacement₹520/ sq ftYou pay this rate for the square feet we measure on site.See this fix
Balcony Glass Replacement₹553/ sq ft₹65015% offYou pay this rate for the square feet we measure on site.See this fix
Glass Railing Clamp Replacement₹425/ clamp₹50015% offOne fixed price per clamp, supplied and fitted.See this fix

Not sure which one it is? Send a photo or a short video. We will tell you what it looks like, usually within minutes, before anyone comes out.

Common questions

Can toughened glass really break on its own, with nobody near it?

Yes, though it is rare. A nickel sulphide speck inside the glass can swell over years until the panel bursts. An old edge chip can also let go long after the knock that made it. Both look like a break from nowhere.

How do I prove it was an inclusion and not something we did?

Only a laboratory can prove it, by finding the speck in the piece where the break began. That test is not work we do. If you want to claim against a supplier, keep the pieces around the break origin in a box.

What is heat-soaked glass, and should my new panel be heat-soaked?

Heat soaking bakes toughened glass in an oven for hours after it is made. A panel with a dangerous speck usually breaks in the oven instead of in your home. It costs a little more and takes longer to supply. We suggest it for railings, high balconies and large shower panels.

Why did the glass turn into small cubes rather than big sharp pieces?

Toughening puts the surface of the glass under stress. When that stress releases, the whole panel breaks at once into small blunt pieces. That is the point of safety glass. Laminated glass goes further and keeps the pieces stuck to its inner layer.

Related problems

Other problems with the same kind of door, window or fitting, and where to go next.

Get it fixed at your place

We come to you anywhere in Bengaluru, Delhi NCR, Mumbai MMR and Pune. We find the cause, and give you a fixed price before any work starts.

  • Toughened safety glass, at the thickness stated in your written quote.
  • The fittings, finish and supplied parts are named before you approve the job.
  • We source the glass and fittings against the specification in your written quote.
  • We check the quality before we leave. Most jobs are done in 3 to 4 days.
  • No hidden fees. GST is shown as its own line on the quote.
  • Your details stay protected and confidential on a secure connection.
  • You get dedicated support after fitting, from the same team every time. They are dependable.
  • Easy and transparent from the first message. We work customer-first, so the job stays hassle-free.
Chat on WhatsApp