At your location in just 29 minutesGet the measurements right away.T&C

Illustration: A dented and kinked running rail beneath a sliding balcony door

Sliding doors · Bengaluru, Delhi NCR, Mumbai MMR and Pune

Sliding Door Track Damaged? Causes & Repair Cost

The track, called the channel in India, is usually repaired in place rather than replaced.

₹1,710 starting price₹1,90010% off

The starting price for Sliding Door Track Repair, the commonest fix. One visit covers travel and the work to fix the fault. Any parts are priced on their own line.

  • Verified on-site measurement
  • 2-year product warranty, 6 months on the work
  • Fitted by our own team. We never subcontract.
Also searched as

The short answer

A damaged sliding door track usually has a groove worn into it by a roller that stopped turning. Rust from rainwater standing in the channel is the next cause, and a dent from a dropped object the third. Most tracks are repaired in place with a stainless steel insert over the worn length. A track worn through, on a frame past saving, means a new door.

The useful distinction

Run a finger along the track to tell wear from rust

A smooth dip in the track is wear from a roller that stopped turning. Rough brown pitting is rust from water that stood in the channel. A sharp step or a crack marks a knock at one place. The shutter stops or jumps there every time it passes.

Why it happens

Usually one of these 5 things, commonest first. Each one says how to tell, and what we do about it.

  1. A seized roller has worn a groove into the track

    How to tell
    The channel, the Indian word for the track, has a shiny dip along part of its length. The shutter drops into it and climbs out with a bump. The roller that caused it no longer turns.
    What we do
    We fit a stainless steel cap or insert over the worn length, so the rollers run on a fresh surface. New rollers go in to match it, and we price them before we start.
    Sliding Door Track RepairFrom ₹1,710See this fix
  2. Water stood in the channel and rusted it

    How to tell
    The track is brown and pitted, worst at the ends where water collects. The drain slots at the bottom of the frame are blocked with mud. It got worse after the monsoon.
    What we do
    We clear the drain slots so water leaves the channel. Then we clean the rust back and fit an insert where the surface is pitted.
    Sliding Door Track RepairFrom ₹1,710See this fix
  3. Something was dropped on it and bent a section

    How to tell
    There is a dent, a raised lip or a crack at one place. The shutter stops or jumps there every time. The rest of the track is fine.
    What we do
    We dress a small dent back and file the lip smooth. A cracked or badly bent length is cut out and a new piece let in.
    Sliding Door Track RepairFrom ₹1,710See this fix
  4. The track is worn through on an aluminium door

    How to tell
    The channel is worn thin or holed, not just grooved. The frame corners have opened and the shutter no longer sits square. An insert would have nothing sound to sit on.
    What we do
    We replace the door with a new aluminium sliding door made to the opening. The new frame has its own track, so the problem does not come back.
    Aluminium Sliding DoorsFrom ₹650 / sq ftSee this fix
  5. A uPVC track has split or the frame has bowed

    How to tell
    A uPVC track is part of the frame and cannot be filed. The track has split, or the frame has bowed so the shutter binds. Parts of the frame have gone chalky and brittle.
    What we do
    We fit a new uPVC sliding door to the opening. The track comes as part of the new frame, with rollers matched to it.
    uPVC Sliding DoorsFrom ₹650 / sq ftSee this fix

What you can check first

These checks are safe to do yourself. A photo or a short video of what you find helps us come prepared.

  • Run a clean finger along the track and feel for a dip, a step or pitting.
  • Look at the ends of the track for rust and for mud in the drain slots.
  • Slide the shutter slowly and note whether it drops, jumps or stops at one place.
  • Do not pack the groove with tape, card or wood, which only hides the dip.
  • Take a close photo of the worst part of the track in daylight.

What the repair costs

Every fix on this page, with its starting price before GST. We find which one you need, and you get a fixed price before any work starts.

FixStarting priceHow it is pricedLink
Sliding Door Track Repair₹1,710₹1,90010% offOne visit covers travel and the work to fix the fault. Any parts are priced on their own line.See this fix
Aluminium Sliding Doors₹650/ sq ftYou pay this rate for the square feet we measure on site.See this fix
uPVC Sliding Doors₹650/ sq ftYou pay this rate for the square feet we measure on site.See this fix

Not sure which one it is? Send a photo or a short video. We will tell you what it looks like, usually within minutes, before anyone comes out.

Common questions

Can a worn sliding door track be repaired without changing the whole door?

Usually, yes. A stainless steel insert fits over the worn length and gives the rollers a fresh surface. The frame stays as it is. Only a track worn through, or a frame past saving, needs a new door.

Why does the sliding door track get damaged every few years?

A roller that stops turning drags on the track instead of rolling. It wears a groove in a few months. Changing a seized roller early is what saves the track.

Does a new track insert need new rollers too?

Yes. The old rollers that wore the groove are worn themselves, and they would score the new insert. We fit rollers matched to the insert and to the weight of the shutter.

Why is my sliding door track rusting when the door is aluminium?

The track is often a steel strip set into the aluminium, and that strip rusts. Water stands on it when the drain slots are blocked. Clearing the slots after each monsoon keeps the strip dry.

Related problems

Other problems with the same kind of door, window or fitting, and where to go next.

Get it fixed at your place

We come to you anywhere in Bengaluru, Delhi NCR, Mumbai MMR and Pune. We find the cause, and give you a fixed price before any work starts.

  • Toughened safety glass, at the thickness stated in your written quote.
  • The fittings, finish and supplied parts are named before you approve the job.
  • We source the glass and fittings against the specification in your written quote.
  • We check the quality before we leave. Most jobs are done in 3 to 4 days.
  • No hidden fees. GST is shown as its own line on the quote.
  • Your details stay protected and confidential on a secure connection.
  • You get dedicated support after fitting, from the same team every time. They are dependable.
  • Easy and transparent from the first message. We work customer-first, so the job stays hassle-free.
Chat on WhatsApp