
Glass doors · Bengaluru, Delhi NCR, Mumbai MMR and Pune
Door Closer Not Closing Door Fully? Causes & Repair Cost
A door closer that leaves the door ajar is usually set wrong or worn out, not broken.
₹2,300 starting price
The starting price for Glass Door Repair, the commonest fix. One visit covers travel and the work to fix the fault. Any parts are priced on their own line.
- Verified on-site measurement
- 2-year product warranty, 6 months on the work
- Fitted by our own team. We never subcontract.
The short answer
A door closer that does not close the door fully usually has its latch speed set too slow. Latch speed is the last short push that takes the door into the frame. The other causes are a closer that has lost its oil, and a door that has moved. A moved door is one the closer cannot pull home. Setting the closer is one visit, and a worn closer is changed on the same visit.
The useful distinction
Watch where the door stops, not how it travels
A door that stops short at the same place every time needs setting. A door that stops in different places is usually catching on something. A door that creeps shut over many seconds has its speed set too slow.
Why it happens
Usually one of these 5 things, commonest first. Each one says how to tell, and what we do about it.
The latch speed is set too slow
- How to tell
- The door swings most of the way, then slows and stops just short of the frame. A gentle push closes it. Nothing is leaking, and the door moves freely by hand.
- What we do
- A closer has two settings: the sweep, which is the main swing, and the latch, which is the last part. We set the latch so it finishes the close firmly without a bang. Then we test from wide open and from halfway.
Glass Door RepairFrom ₹2,300See this fixThe closer has lost its oil
- How to tell
- The door used to shut fully, and over months it has started stopping short. There may be an oily ring around the floor plate, or a streak under the arm. Turning the screws no longer changes anything.
- What we do
- Oil is what gives the closer its push at the end of the swing. Once it has leaked, we replace the unit with one rated for your door. A floor spring goes into the same floor box, and an arm closer onto the same frame.
Glass Door Closer ReplacementFrom ₹3,900 / doorSee this fixThe door has dropped, so the closer cannot pull it home
- How to tell
- The door catches the floor or the frame near the end of its swing. A gap shows along the top on one side. The closer is pushing, but the rub is holding the door back.
- What we do
- We lift the door back to its height on its pivot or hinges and square it in the frame. Once it swings clear, the closer is often fine. We check the settings after that, not before.
Glass Door AlignmentFrom ₹2,070See this fixThe arm or the spindle has worn
- How to tell
- On a framed door the arm has play at its joints and rattles. On a frameless door the spindle, the square shaft the door turns on, has worn round. The door moves on the fitting before the closer takes it.
- What we do
- A worn arm is changed on its own where the body is still sound. A worn spindle means a new floor spring, because the two are one unit. We tell you which before anything is ordered.
Glass Door Closer ReplacementFrom ₹3,900 / doorSee this fixSomething is holding the door back
- How to tell
- A stopper or a mat sits where the door should finish its swing. A carpet or a door seal added later rubs the bottom edge. The door closes fully when you lift the mat away.
- What we do
- We move the stopper, reset a seal that drags, and set the closer after that. This is adjustment work on the visit, with no new part.
Glass Door RepairFrom ₹2,300See this fix
What you can check first
These checks are safe to do yourself. A photo or a short video of what you find helps us come prepared.
- Open the door wide and let it go, then open it halfway and let it go again.
- Look at the base of the door for an oily ring, and under an arm closer for a streak.
- Lift the door slightly by its handle and see if it then closes fully.
- Try at most a quarter turn on the latch screw, and stop if nothing changes.
- Note whether the door stops at the same place every time, or in different places.
What the repair costs
Every fix on this page, with its starting price before GST. We find which one you need, and you get a fixed price before any work starts.
| Fix | Starting price | How it is priced | Link |
|---|---|---|---|
| Glass Door Repair | ₹2,300 | One visit covers travel and the work to fix the fault. Any parts are priced on their own line. | See this fix |
| Glass Door Alignment | ₹2,070 | One visit covers travel and the work to fix the fault. Any parts are priced on their own line. | See this fix |
| Glass Door Closer Replacement | ₹3,900/ door | One fixed price per door, supplied and fitted. | See this fix |
Not sure which one it is? Send a photo or a short video. We will tell you what it looks like, usually within minutes, before anyone comes out.
Chat on WhatsAppA photo or a video is enough to startCommon questions
Why is my door closer not closing the door all the way?
Most often the latch speed, the setting for the last part of the swing, is too slow. The door loses its push just before the frame and rests there. Less often the closer has lost oil, or the door has dropped and rubs. Lifting the door by its handle tells you whether it rubs.
Which way do I turn the screw on a door closer to make it close faster?
On most closers, turning a screw clockwise slows that part of the swing, and anticlockwise speeds it up. Turn the latch screw a quarter turn at a time and test. Never wind a screw all the way out, because the oil inside comes out with it. Then the closer is finished and has to be changed.
Is a door closer that stops short the same fault as one leaking oil?
Not always. A leaking closer stops short because its oil is going. That fault has its own page, door closer leaking oil. A dry closer that stops short usually only needs setting. Look at the floor plate or under the arm first, and the oil tells you which page you need.
Does a door that stops short matter if it is only a cabin door?
It matters more than it looks. An office cabin door left ajar lets sound through and stops the lock from catching. A shop door left open lets the cool air out all day. Setting the closer is a small job, and it saves the glass being pushed by hand every time.
Related problems
Other problems with the same kind of door, window or fitting, and where to go next.
Glass doors
- Glass Door Not Closing Properly
- Glass Door Closing Too Fast
- Glass Door Making Noise
- Glass Door Rubbing on the Floor
- Glass Door Handle Loose or Broken
- Glass Door Not Locking
- Door Handle Hitting the Wall
- Gap Between Glass Doors
- Glass Door Cracked
- Glass Door Shaking or Loose
- Door Closer Leaking Oil
- Door Closer Making Noise
- Shop Front Glass Broken
Same fixes, other problems
Get it fixed at your place
We come to you anywhere in Bengaluru, Delhi NCR, Mumbai MMR and Pune. We find the cause, and give you a fixed price before any work starts.
- Toughened safety glass, at the thickness stated in your written quote.
- The fittings, finish and supplied parts are named before you approve the job.
- We source the glass and fittings against the specification in your written quote.
- We check the quality before we leave. Most jobs are done in 3 to 4 days.
- No hidden fees. GST is shown as its own line on the quote.
- Your details stay protected and confidential on a secure connection.
- You get dedicated support after fitting, from the same team every time. They are dependable.
- Easy and transparent from the first message. We work customer-first, so the job stays hassle-free.