At your location in just 29 minutesGet the measurements right away.T&C

Illustration: Broken shopfront pane with a missing section and glass fragments below

Glass doors · Bengaluru, Delhi NCR, Mumbai MMR and Pune

Shop Front Glass Broken? Causes & Repair Cost

A broken shop front needs making safe first, and the next panel needs the reason fixed.

₹416/ sq ft starting price₹52020% off

The starting price for Mirror & Custom Glass Installation, the commonest fix. You pay this rate for the square feet we measure on site.

  • Verified on-site measurement
  • 2-year product warranty, 6 months on the work
  • Fitted by our own team. We never subcontract.
Also searched as

The short answer

A broken shop front is usually an impact from outside. The next cause is a door that swung into the fixed panel beside it. The glass is toughened, so it breaks into small pieces rather than long shards, but the pieces still cut. We make the opening safe, measure it, and fit a new panel made to that size. Before the new glass goes in, we fit a stopper or reset the door. Then the same break cannot happen again.

The useful distinction

Separate a struck panel from a door that struck something

A panel struck from outside shows the smallest pieces around one spot. A door whose own edge cracked usually hit a frame or a wall first. A fixed panel broken along the door edge means the door swung into it.

Why it happens

Usually one of these 4 things, commonest first. Each one says how to tell, and what we do about it.

  1. Something struck the panel from outside

    How to tell
    The break starts at one spot, with the smallest pieces around it. A stone, a trolley or a vehicle bumper often leaves that mark low down. The rest of the panel may still stand in its frame, held by film or beading.
    What we do
    We clear the broken glass and secure the opening. We measure the frame and have a toughened panel made to that size. Toughened glass cannot be cut after it is made, so the measuring is the job.
    Mirror & Custom Glass InstallationFrom ₹416 / sq ftSee this fix
  2. The door swung into the fixed panel with nothing to stop it

    How to tell
    The fixed panel broke at the edge nearest the door. The door opens fully until its handle or its edge meets that panel. There is no stopper on the floor or the wall.
    What we do
    We fit a stopper, a small steel or rubber dome fixed to the floor, where the door should stop. It takes the knock that the glass was taking. We set it so the door still opens wide enough for a trolley.
    Glass Door Stopper InstallationFrom ₹553 / pieceSee this fix
  3. The door has dropped and its glass hits its own frame

    How to tell
    The door scrapes at the bottom or catches the frame on the closing side. Small chips show on the edge of the door where it has been striking. The break began at one of those chips.
    What we do
    We reset the door on its pivot or hinges so it swings clear. On a frameless door we check the patch fittings, the metal clamps at the top and bottom corners. A new panel put into a dropped door would chip the same way.
    Glass Door RepairFrom ₹442See this fix
  4. The old panel was ordinary glass, not toughened

    How to tell
    The glass broke into long, sharp pieces instead of small cubes. Some pieces still hang in the frame. Older shop fronts in a market or a plaza are often glazed this way.
    What we do
    The new panel is toughened safety glass, which is the right glass for a shop front. We suggest the thickness from the size of the opening and how busy the entrance is. We tell you what we recommend before it is ordered.
    Mirror & Custom Glass InstallationFrom ₹416 / sq ftSee this fix

What you can check first

These checks are safe to do yourself. A photo or a short video of what you find helps us come prepared.

  • From a safe distance, take photos of the whole front and of where the break starts, before anything is moved.
  • Look at the floor and the wall beside the door for a stopper, and for marks where the door lands.
  • Check whether the pieces are small cubes or long shards, because that tells us what glass you had.
  • Measure the width and height of the opening roughly, so we can bring the right cover.
  • Keep the shutter down, or the shop staffed, until the opening is secured.

Keep customers and staff away from the broken panel now. Do not pull at pieces still in the frame, because a panel can let go all at once. Tape or board only what you can reach without touching the glass, and leave the rest to us.

What the repair costs

Every fix on this page, with its starting price before GST. We find which one you need, and you get a fixed price before any work starts.

FixStarting priceHow it is pricedLink
Mirror & Custom Glass Installation₹416/ sq ft₹52020% offYou pay this rate for the square feet we measure on site.See this fix
Glass Door Stopper Installation₹553/ piece₹65015% offOne fixed price per piece, supplied and fitted.See this fix
Glass Door Repair₹442₹52015% offOne visit covers travel and the work to fix the fault. Any parts are priced on their own line.See this fix

Not sure which one it is? Send a photo or a short video. We will tell you what it looks like, usually within minutes, before anyone comes out.

Common questions

Can a broken shop front be replaced the same day?

The making safe can usually happen the same day. The panel itself is made to your measurements, because toughened glass cannot be cut or drilled afterwards. How long that takes depends on the size and the thickness. We cover the opening while you wait.

Why did my shop glass break when nothing hit it?

Usually something did, earlier. A chip from a trolley or a shutter weeks before weakens toughened glass at that spot. It can then break on a hot afternoon or a hard door close. A door with no stopper is the most common earlier knock.

Should a shop front use toughened or laminated glass?

Toughened glass breaks into small pieces, so it is the usual choice for a shop front. Laminated glass holds together when it breaks, which some shops prefer for security. It is heavier and needs a stronger frame. We can fit either, and we suggest which suits your frontage.

Can the shop stay open while the new glass is being made?

Usually, yes. We board or screen the opening on the first visit so the shop stays secure. The door keeps working where it is not the broken part. Tell us if the front has to look presentable, and we use a clean board.

Related problems

Other problems with the same kind of door, window or fitting, and where to go next.

Get it fixed at your place

We come to you anywhere in Bengaluru, Delhi NCR, Mumbai MMR and Pune. We find the cause, and give you a fixed price before any work starts.

  • Toughened safety glass, at the thickness stated in your written quote.
  • The fittings, finish and supplied parts are named before you approve the job.
  • We source the glass and fittings against the specification in your written quote.
  • We check the quality before we leave. Most jobs are done in 3 to 4 days.
  • No hidden fees. GST is shown as its own line on the quote.
  • Your details stay protected and confidential on a secure connection.
  • You get dedicated support after fitting, from the same team every time. They are dependable.
  • Easy and transparent from the first message. We work customer-first, so the job stays hassle-free.
Chat on WhatsApp