Is this the right service for your job?
Choose this for glass that is clear at a switch and frosted at the next, on a cabin, a meeting room, a clinic or a bathroom.
- If you are building the cabin or meeting room from scratch and privacy can be a frosted film, see the Office Glass Partition with Door. A new partition with a fixed frosted band costs less than switchable glass.
- If the entrance rather than the wall is the thing to automate, see the Automatic Sliding Doors. A sensor door opens and closes itself; it is a different machine from switchable glass.
Smart film on your glass, or new laminated smart glass
Smart film is a self-adhesive PDLC sheet, cut to each pane and bonded to the inside face of glass that is already fitted. It is the quicker and lower-priced way, and it suits a cabin or a meeting room that already has glass walls. The film carries a thin busbar along one edge that connects to the transformer.
Laminated smart glass has the PDLC layer sealed between two sheets of toughened glass. It is the right choice for a new partition, a shower screen or a bathroom window, because the layer is protected from water and from cleaning. It is heavier and costs more, and the panel is made to size before it is fitted.
Both switch in well under a second and both are controlled the same ways.
Where switchable glass is used
In offices, on the glass of a cabin or a meeting room, so a call can be private without blinds. In clinics and hospitals, between a consulting room and the corridor, or around a treatment bay. In hotels and homes, between a bedroom and its bathroom, where the glass stays clear for light and frosts for privacy.
In shop fronts and showrooms, a switchable front can be frosted after hours. On a street-facing window at home, it replaces a curtain that is always drawn. Anywhere a blind or a frosted sticker is doing the job today, switchable glass does it without hiding the light.
Power, control and what happens when the power goes
The glass runs on low voltage from a transformer that plugs into a normal socket. Each pane has a busbar on one edge, and the cable from it runs to the transformer through the frame or a slim trunking. It uses very little power, about what a small bulb does, and only while clear.
Control is a wall switch, a remote, a motion sensor or a smart home relay, and several panes can run from one transformer. When the power goes, the glass turns frosted. For a bathroom that is the safe way round. For a meeting room where you want it clear by default, we can wire it through an inverter supply.
The wiring is an electrician's work; we fit the glass, the busbars and the transformer and leave a clean connection point.
Switchable glass price per sq ft, and what changes it
The rate starts at ₹1,400 per sq ft for smart film bonded to glass you already have, fitted with a transformer, before GST. Laminated smart glass panels cost more, and the frame or clamps for a new partition are priced on their own lines.
A cabin wall eight feet by ten feet is 80 sq ft. Multiply by the current rate above for a rough figure before extras and GST. The number of separate panes matters, because each needs its own busbar and connection, so many small panes cost more than one large one.
You get a written price after the measuring visit. It lists each pane, the film or panel, the transformer and the control.
From the measuring visit to a working switch
Send a photo of the glass or the opening on WhatsApp, or book the measuring visit. At the visit we measure each pane, check the frame for a route for the busbar cable, and agree where the transformer and the switch will go.
Then you get the written price. Once you agree, you pay an advance, because film and panels are cut to your sizes. Fitting smart film on existing glass usually takes a day. New laminated panels are made first and fitted on a later day.
You pay the rest when every pane switches cleanly and the connection is tidy.
Care, and what to expect over time
Clean switchable glass with a soft cloth and a mild glass cleaner, never a blade or an abrasive pad. Smart film is on the inside face, so cleaning stays gentle on that side. Laminated smart glass cleans like any glass.
The PDLC layer dims very slightly over many years of use, and the frosted state can take on a faint tint in direct afternoon sun. Film that is kept dry and clean lasts many years. The transformer is a plug-in unit that can be changed on its own if it ever fails.























